Tata ELXSI Paper

Paper Type : Technical - Electronics
Posted By : admin


TATA ELXSI PAPERS HELD AT DRIEMS ,CUTTACK ON 24th APRIL 2004

There were two rounds 1)TECH(30 ques,30 mins)2)APTITUDE(30 ques,30 mins)

TECH QUESTIONS (Electronics & TC)

1.

CMRR is given=
Differential gain is given=
Inputs:
+ve end=2v,-ve end=1v of the OP-AMP
Find the output voltage?
2.

CRO is in X-Y mode.Sinusoidal inputs have 90degrees phase difference between them. What will appear on the display? a)circle b)line c)ellipse d)triangular wave
3.

Which has least propagation delay?
a)ECL b)TTL c)RTL d)CMOS
4.

In a ripple counter how many change in states happen when count changes from7 to 8?
a)1 b)2 c)3 d)4
5.

Max. no. of variables that can be represented in K-MAP?
a)3 b)5 c)7 d)none of these
6.

How many comparators are required in a n-bit flash ADC?
a)2^(n-1) b)(2^n)-1 c)2^n d) n
7.

What is an EEPROM?
a)Programmable transistor
b)Transistor
c)SRAM
d)
8. Time period of input voltage=8ns. / Find the duty cycle of Vout.

Voltage across one capacitor is V volts. Another cacitor is added at its one end(now the two are in series). What is the voltage across their ends?
a)V b)V/2 c)2v d)none of these
9.

In an SCR why silicon is used?
a) available easily
b) has much less reverse saturation current than Germanium
c) has greater reverse sat.current than Ge
d)
10. Output=?


a)A’+B’+C
b)A+B+C’
c)A(B’+C’)
d)B’+C’+A’
11. There was a question using transmission gates.Three inputs were A,B,C.Answer was (A+BxorC)
12. How to get the characteristic figure changed from 1 to 3?(characteristic diagram)


a)By increasing gate width of NMOS
b)---------do----------------- of CMOS
c)By increasing gate voltage

14. Find propagation delay?

a)200Hz b)150Hz c)5Hz d)2Hz
15.

A diagram was given to identify?
a)Synchronous counter
b)Ripple counter
c)Shift register
d)None of the above
answer was sync. Counter
16. Find Va?and Ia, Ib?

17. Find ammeter current Ia?

a)10V b)9.09V c)11.01V d)0.9V these options may be wrong.
18.


This acts as a:
a)OR
b)XOR
c)AND
d)NOR
19.

At t=0 if position is changed from 1 to 2 ,find the voltage across 1KΩ?

a)4V b)2V c)1.5V d)none of these
20.

Find thevenin voltage and resistance across A and B

21.

how will be the output voltage across R ?




Ans C
22.

What is this ?


a)Integrator b)Differentiator c)Antilog differentiator d)Log differentiator
23.



Flip-flop state diagram question.What does the above represent?
24.

What is this?


a)Squaring device b)Divider c)Square root ckt d)
25.

How will be the output vs. input graph if Vin=10V,sat voltage of OP-amp is 14V?


26.

Basic memory cell of dynamic RAM a. Capacitance
b. Flip flop
c. Transistor
d. Transistor with Capacitor
27.

Ideal Power Supply has
a. Zero internal resistance
b. High O/P resistance
c. High I/P resistance Freshersworld.com
d. Low O/P resistance
28.

Which type of transmission line will have max. value of characteristic impedence a. Open Wire line b. Coaxial Cable
c. Twin lead line d. None
29.

For same peak value of current, which waveform will have least RMS value a. Sine b. Square
c. Triangular
d. Full wave rectified wave
30.

-V analogy displacement is analogous to
a. Voltage b. Condutance
c. Magnetic Flux Linkage
d. Capacitance
Similarly..............In F-I analogy displacement is analogous to
a. Charge
b. Resistance Freshersworld.com
c. Inductance
d. Current
31.

In the following circuit Vo/Vin = (there were 4 options)

32.

In the following circuit the charging and discharging time is (i don’t remember the options)

Don't remember the other value of other res and cap .But some values are given
33.

The output at X acts as….

a.OR gate
b.AND gate
c.XOR gate
d.XNOR gate
34.

The CRO in X-Y mode gives the following figure. If signal applied to the Y-plate is 2sin(wt) then the signal applied to the X is a. 2 sin (wt) b. 2 sin (wt + p/4) c. 2 sin (wt d.2Ö2 sin (wt + p/4)

Related Articles :